Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Plloyd Strikes Again
01-10-2015, 01:30 AM,
#1
Plloyd Strikes Again
Our own graphics wizard has contributed new "official" images to the PG line once again, this time Trucks in SS camo for use in PG.
Reply
01-12-2015, 09:55 PM,
#2
RE: Plloyd Strikes Again
(01-10-2015, 01:30 AM)larry marak Wrote: Our own graphics wizard has contributed new "official" images to the PG line once again, this time Trucks in SS camo for use in PG.

Is it only me, or does nothing download when you click on the AVP link to the pdf? Huh
Tim
Reply
01-13-2015, 12:00 AM,
#3
RE: Plloyd Strikes Again
It's only you. I didn't have a problem. If it still doesn't work, I could send you a copy.
... More and more, people around the world are coming to realize that the world is flat! Winking
Reply
01-13-2015, 12:47 AM,
#4
RE: Plloyd Strikes Again
Tim,

You're not the first one who had issues downloading files from the websites. Easiest I've found is to right-click on the "New transport pieces" and select "Save Link As..." from the popup menu.
Reply
01-13-2015, 06:11 AM,
#5
RE: Plloyd Strikes Again
Thanks for the advice. The link finally worked for me a couple of minutes ago Smile

Great job, Peter - these counters fill large gaps in a lot of scenarios. Now to get printing and mounting ready for Winter Soldiers #1!

Tim
Reply
01-13-2015, 06:15 AM, (This post was last modified: 01-13-2015, 06:16 AM by plloyd1010.)
#6
RE: Plloyd Strikes Again
That is what they were intended for. Smile

Fold along the dashed line. Everything should be obvious after that.
... More and more, people around the world are coming to realize that the world is flat! Winking
Reply
02-01-2015, 05:29 AM, (This post was last modified: 02-01-2015, 05:32 AM by Bluebell88A.)
#7
RE: Plloyd Strikes Again
I thought that I would share a pic of my DIY SS Truck counters before (on the left) and after (centre) spraying with gloss varnish. Note how the black numbers and vehicle drawing have become much more pronounced, and compare favourably with the PzIV counter from Elsenborn Ridge.

The counters were printed on an A4 label sheet, stuck onto 1.4mm mounting board, side cut into strips and individually cut using a large pair of kitchen scissors. I finished them off with a No.18 X-Acto blade in a "C4 corner cutter".

I mounted the counters on a piece of card using White Tack, then sprayed them with 3 thin layers of inkjet paper gloss varnish 24 hrs apart (warning: the varnish smells until it has set!). This ensures that the varnish is not damaged during the cutting process, and it helps to seal the edges. The counters were then turned over for the reverse sides to be sprayed.

They look and feel very similar to regular PG counters.

Tim


Attached Files Image(s)
   
Reply
02-01-2015, 07:02 AM,
#8
RE: Plloyd Strikes Again
They look good to me. I have a C4 cutter too, which i have largely worn out. I got a nice 2mm cutter to replace it.

Good job Tim!
... More and more, people around the world are coming to realize that the world is flat! Winking
Reply
02-01-2015, 07:58 AM,
#9
RE: Plloyd Strikes Again
Great timing! I was going to post and ask if anyone put a coating on their DIY pieces and what they used. Thanks!
Reply
02-01-2015, 10:27 AM,
#10
RE: Plloyd Strikes Again
Now for a question completely different... Did anyone try the Vassal addon I made for Shad's AB:IE module. I saw that Mike put it in a string of daily content posts he put up about 2 weeks ago. I was wondering how it worked for anyone else.
... More and more, people around the world are coming to realize that the world is flat! Winking
Reply


Forum Jump:


Users browsing this thread: 3 Guest(s)